How To Create Your Portable Voltage Divider
When you are designing a piece of audio equipment, one of your major concerns is how you get to regulate or control its volume. In this case, a potentiometer which is a variable resistor may be used for specific adjustments. The device used in this situation helps you gain controls for any variable.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
Knowing these essentials, you may realize that you can also create your own portable divider. For this, you have to prepare the leads, resistors, alligator clamps, snap on connectors, a voltmeter and a standard 9V battery. This is the highest possible amount of V a simple electronic can handle. Some would limit it to a 5V only.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Putting together the two leads. Twist together both lead ends and lock it up using the last alligator clamp. After doing so, take the connector of your voltmeters then do the correct terminal placing. Red wires go to the positive terminal of your battery while the black wires refer to the negative one. Then you can start turning your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
In some cases, devices which involve circuitry and an equation are produced as an aid to these situations. Known as the most fundamental circuit, this tool is called a Voltage Divider. It is a passive circuit which helps reduce the large volumes of your audio equipment or other electronics.
Using two resistors, this divider shall allow you to turn a large voltage into a smaller one provided that you also have the value of input voltage. Understand how this device works need you to be familiar with the Ohms law which states, the direct current flowing in a conductor is directly proportional to the potential difference between its ends.
This divider has two main parts namely the circuit and the equation. To make it work, first, you should secure a circuit by putting in two resistors together. The equation, on one hand, allows you to calculate the output after you have found the ratio of both resistors while considering the input volt as another variable.
Knowing these essentials, you may realize that you can also create your own portable divider. For this, you have to prepare the leads, resistors, alligator clamps, snap on connectors, a voltmeter and a standard 9V battery. This is the highest possible amount of V a simple electronic can handle. Some would limit it to a 5V only.
Begin by connecting the leads with an alligator clamp. One should contain the red lead resistor with 10 Ohms and the other should contain the black one which has 20 ohms. Then after connecting these leads, use the free end to twist these two together.
Putting together the two leads. Twist together both lead ends and lock it up using the last alligator clamp. After doing so, take the connector of your voltmeters then do the correct terminal placing. Red wires go to the positive terminal of your battery while the black wires refer to the negative one. Then you can start turning your meter on.
As you can see from 9V, your voltage goes down to 3V. When this happens, the positive terminal of the circuit is now the one where the twist is located. Meanwhile, the negative terminal is retained as the negative source.
Creating your own portable device is just easy. However, you have to take safety measures for this. When dealing with a 9V battery, however, you may not see a lot of danger for it in terms of electrocution possibilities. But for other electronics, make sure that you have unplugged the wires before working on it.
About the Author:
When you are searching for the facts about a voltage divider, come to our web pages. More details are available at http://www.rossengineeringcorp.com/products/measurement/hv-voltage-dividers/hv-voltage-dividers-detailed-info.html now.
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment