Understanding What Electronic Boards In LCD TVs, The T-Con D50ud1 For Instance, Really Do
There was a time when television sets were not comprised of much more than a tube encased in wood, fuses, wires, a scanner, some knobs, and a set of rabbit ears. Like most things in today's world, televisions are more complicated now. You may never want to be a television repair person, but if you have any interest in electronics, it can be instructive to learn about the primary boards, like the T-Con d50ud1, found in LCD tvs.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
The direct current will only move in one direction. This is what the circuit in LCD televisions uses. Depending on the model you have the power supply module and the inverter board may be combined. If you're not getting any power, or only intermittent power, the power supply board may be to blame.
The T-Con, or timing control board, will be the smallest board on the panel. LCD televisions are the only ones that have them. These boards are usually covered by a shield and are located on the top back of your panel.
The purpose of the T-con board is to control the circuit and TFT, or thin film transistor, driver. Indications that you have trouble with the T-con board will be vertical or horizontal lines. You might also see a double image, a white screen or no display.
Inverter boards are found along the edge of your television back. Unless you have an LCD television you will not have an inverter board. The purpose of this board is to convert low voltage direct current supplied by the switched mode power supply into high voltage alternate current. This is what lights up the backlights. Sometimes it's included in the power board. If you have a dim screen or the display shuts down, you have a problem with the inverter board.
The main board is also called the main module, the digital or logic board, or the motherboard. The video and audio inputs and outputs are attached to it. The main board converts signals from analog to digital. If you're having trouble with the sound or the color, it may be the main board.
The jackpack or audio receiving board is sometimes separated from the main board. Its function is to take the sound signal to the processor and on to the amplifier which is what drives the speakers on either side of the television. If you don't have sound, or a high pitched one, or channels that change randomly, you need to have the jackpack checked out.
If you open up the back of your television set you will probably find the power supply board, or power supply module, on the right hand side of your unit as you are looking at it. It will be the largest and heaviest of all the boards on the back of the set. The purpose of this board is to convert the AC, or alternating current, supply, which can change directions, into DC, or direct current, voltage.
The direct current will only move in one direction. This is what the circuit in LCD televisions uses. Depending on the model you have the power supply module and the inverter board may be combined. If you're not getting any power, or only intermittent power, the power supply board may be to blame.
The T-Con, or timing control board, will be the smallest board on the panel. LCD televisions are the only ones that have them. These boards are usually covered by a shield and are located on the top back of your panel.
The purpose of the T-con board is to control the circuit and TFT, or thin film transistor, driver. Indications that you have trouble with the T-con board will be vertical or horizontal lines. You might also see a double image, a white screen or no display.
Inverter boards are found along the edge of your television back. Unless you have an LCD television you will not have an inverter board. The purpose of this board is to convert low voltage direct current supplied by the switched mode power supply into high voltage alternate current. This is what lights up the backlights. Sometimes it's included in the power board. If you have a dim screen or the display shuts down, you have a problem with the inverter board.
The main board is also called the main module, the digital or logic board, or the motherboard. The video and audio inputs and outputs are attached to it. The main board converts signals from analog to digital. If you're having trouble with the sound or the color, it may be the main board.
The jackpack or audio receiving board is sometimes separated from the main board. Its function is to take the sound signal to the processor and on to the amplifier which is what drives the speakers on either side of the television. If you don't have sound, or a high pitched one, or channels that change randomly, you need to have the jackpack checked out.
About the Author:
See the featured products including the d50ud1 by referring to the Web. Spend a minute or two browsing the online store at http://www.tekbyus.com/product-tag/d50u-d1.
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment