How To Install A Grounding Rod
It is important to have your house or permanent structure properly grounded if you have electricity in the building. This can help prevent a fire should lightning strike or some other electrical surge be sent towards the building. Installing a grounding rod properly is very important but also much easier than you might think. There are some regulations in areas on what the requirements are, so be sure to check and see what the rules are in your area. You will also want to ask your utility company to mark where any underground lines are so you avoid hitting them when installing the rod.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
With the spot selected you can begin to dig. If you have a post hole digger, you can dig a couple of feet down easily. Using a shovel is fine, but you do not need to dig a wide hole. Dig the hole as deep as you can before moving to the next step.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
The pole driver works best. It is designed to fit over the pole, making it easy to pound it into the ground without using a hammer, which can miss and hit your hand. If you don't have one, use a two by four or other board to give yourself a larger surface to hit. Keep pounding and driving the pole into the ground until it is just above the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
The first step is to get the right equipment for the job. You may need a post hole digger, shovel, and post driving tool for this job since the rods are usually eight feet long. They are often copper. When you buy one, make sure it is approved material or it will not properly ground your home. This can lead to a very dangerous situation.
Pick your spot first by making sure you are not in a rocky area. Also, be at least a foot to two feet away from the building to avoid rerouting the surge back into the foundation. Finally, you need to dig on the side of the house with the electrical panel.
With the spot selected you can begin to dig. If you have a post hole digger, you can dig a couple of feet down easily. Using a shovel is fine, but you do not need to dig a wide hole. Dig the hole as deep as you can before moving to the next step.
When the hole is dug, add water. This is to help soften the ground so it will be easier to push the pole into the ground. Being by pushing it by hand. You may have to move it around in a circle to help get it through the packed dirt. There will be one end that is pointed and that one should go into the ground. At some point, you won't be able to hand push it in and will need to move to the next step with the tools.
The pole driver works best. It is designed to fit over the pole, making it easy to pound it into the ground without using a hammer, which can miss and hit your hand. If you don't have one, use a two by four or other board to give yourself a larger surface to hit. Keep pounding and driving the pole into the ground until it is just above the hole.
Now you want to attach a ground wire. This will also be attached to your electrical panel, so be sure to handle with care. Some are shielded wires, so you will need to cut the end and expose the copper wire. Use a special clamp to connect to the pole. Make sure there is enough slack in the wire that bumping it will not disconnect it from the rod. You may want to dig a small trench to bury the wire it if is in an area that will be mowed and away from the house a few feet.
Finally, fill in the hole. If the rules require the pole to be completely underground, finish hammering it down and fill it in. In any case, it is best to keep it low enough that a lawn mower blade will not hit is. If you placed it a couple of feet from the building, you might consider burying the wire until it comes up next to the building to protect it from weed eaters and lawn mowers.
About the Author:
Find out how to get a high-quality grounding rod by viewing our web pages today. To access our online catalog of high voltage equipment or to learn more about our certifications, click the links at http://www.rossengineeringcorp.com .
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment