Things That Goes Into Manufacturing Of PCB
Printed circuit boards, otherwise known as PCB are found in almost all electronic devices. In manufacturing of PCB, electricians who are amateurs can make their own boards by drawing a design and then giving it to the manufacturer. There are three types; single sided, multi layered and double side boards. They are usually conducted with nickel, copper or aluminum material, and the type used is determined by the complexity and density of the circuits. The process of making them is described below.
The backing is first plated with a conductive material. Holes are then drilled into it in order for conduction to take place in between the layers and also to mount electronic components. The board is then scrubbed to get rid of any small particles of the conductor. Such particles can be later on recycled from the water by using a process such as filtration. Any copper particles left behind can easily mix with other wastes and become pollutant to the environment.
Cleaning of the board is then done. In the next stage, there should be adequate adhesion and therefore to enhance this, etching is also done. One more layer of conductor is added next. The holes that had been drilled earlier should be conducted; hence the application of electrolysis copper plating is vital. Acidic based solutions and alkaline ones are used so that the pH is properly balanced.
Photo imaging is used to achieve the final design of the circuit. The final thickness is also arrived at by electroplating copper. Protection of the final circuits in the next etching is quite vital and hence, a thin layer of tin or lead solder should be applied. The copper will not form the final circuit and should therefore be removed. Sulfuric acid or a solution containing ammonia is used to etch away the unwanted copper.
Other organic or photosensitive compounds can be used to obtain alternative resists. The compounds can be used when wet or dry. They will become hard when they are exposed to ultraviolet light.
A roller, squeegee, spray or silk screen can be used to apply the liquid resist. The liquid can be applied on either or both sides or just on a specific area on the surface. Light can be used in order to get better circuits.
The last stage is the formation of multi layer panels. This is done by assembling together the inner cores of the layer. The assembled panels take the shape of a book that is composed of copper foil that has epoxy sheets alternating with each other.
The book is then placed in a lamination press and high heat and pressure applied to it. The epoxy layers will melt and form a bond. An oven is used to cure the panel. It also undergoes trimming and buffing and then the required holes are finally drilled into it. Summarily, manufacturing of PCB requires a careful and properly calculated procedure in order to achieve the desired results.
The backing is first plated with a conductive material. Holes are then drilled into it in order for conduction to take place in between the layers and also to mount electronic components. The board is then scrubbed to get rid of any small particles of the conductor. Such particles can be later on recycled from the water by using a process such as filtration. Any copper particles left behind can easily mix with other wastes and become pollutant to the environment.
Cleaning of the board is then done. In the next stage, there should be adequate adhesion and therefore to enhance this, etching is also done. One more layer of conductor is added next. The holes that had been drilled earlier should be conducted; hence the application of electrolysis copper plating is vital. Acidic based solutions and alkaline ones are used so that the pH is properly balanced.
Photo imaging is used to achieve the final design of the circuit. The final thickness is also arrived at by electroplating copper. Protection of the final circuits in the next etching is quite vital and hence, a thin layer of tin or lead solder should be applied. The copper will not form the final circuit and should therefore be removed. Sulfuric acid or a solution containing ammonia is used to etch away the unwanted copper.
Other organic or photosensitive compounds can be used to obtain alternative resists. The compounds can be used when wet or dry. They will become hard when they are exposed to ultraviolet light.
A roller, squeegee, spray or silk screen can be used to apply the liquid resist. The liquid can be applied on either or both sides or just on a specific area on the surface. Light can be used in order to get better circuits.
The last stage is the formation of multi layer panels. This is done by assembling together the inner cores of the layer. The assembled panels take the shape of a book that is composed of copper foil that has epoxy sheets alternating with each other.
The book is then placed in a lamination press and high heat and pressure applied to it. The epoxy layers will melt and form a bond. An oven is used to cure the panel. It also undergoes trimming and buffing and then the required holes are finally drilled into it. Summarily, manufacturing of PCB requires a careful and properly calculated procedure in order to achieve the desired results.
About the Author:
When you need to find reliable manufacturing of PCB, visit the web pages at www.becman.com today. You can see details online at http://www.becman.com now.
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment