DC Regulated Power Supply - Just how To Use
Quite often whenever digital equipment tend not to function and work, we'd immediately suspect a faulty switch mode power. But do you know that substandard or shorted components inside motherboard or main board could result in the power to go wrong too?
Switch mode power (SMPS) are made so proficiently that whenever there does exist any short-term circuit occur mainly board the capability supply would probably shut on their own off and additionally totally cease working. If you have no practical experience about troubleshooting change mode power, you may believe that the power have issue where in fact the main board could be the real trigger of no power problem.
Switch mode power have a present sense circuit (if you look into UC3842 PWM IC pin 3, it suggested I-sense which unfortunately mean ongoing sense) and if you have short circuit inside secondary edge (either in secondary diodes or main board), the current drawn is increase this also will lead the PWM IC to fix generating output to your power fet and thus the power supply would shut down. All that happen in a split involving seconds and you don't need to the possibility to know if there are output voltages in the secondary side. 650 WATT Power Supply for a PC.
Some older design involving SMPS power do not use the PWM IC, nevertheless it do enjoy the circuit to detect across current drawn and closed itself down whenever it detects some shorted component inside secondary side. One superior example was the capability supply utilised in printer. Printers as a rule have two boards; one was the strength supply while the other was main table. If there is any short-term circuit in the main board, the power supply would not work. In order to isolate for where help, one must remove the connector in the power furnish board. Once the supply connector on the main table was taken off, you are now able to switch on the printer and check if there is any voltages present at the power furnish connector. 585 Watt Hot Swap Power Supply may be appropriate for you computer.
If there are actually zero voltages scored across all the supply (VCC) hooks then we could conclude that power give have problem and put your whole concentration in such a power supply board. Can you imagine if there are voltages measured along the connector? Which means the significant board is actually causing this no power problem most probably due for some shorted components primarily board.
Switch mode power (SMPS) are made so proficiently that whenever there does exist any short-term circuit occur mainly board the capability supply would probably shut on their own off and additionally totally cease working. If you have no practical experience about troubleshooting change mode power, you may believe that the power have issue where in fact the main board could be the real trigger of no power problem.
Switch mode power have a present sense circuit (if you look into UC3842 PWM IC pin 3, it suggested I-sense which unfortunately mean ongoing sense) and if you have short circuit inside secondary edge (either in secondary diodes or main board), the current drawn is increase this also will lead the PWM IC to fix generating output to your power fet and thus the power supply would shut down. All that happen in a split involving seconds and you don't need to the possibility to know if there are output voltages in the secondary side. 650 WATT Power Supply for a PC.
Some older design involving SMPS power do not use the PWM IC, nevertheless it do enjoy the circuit to detect across current drawn and closed itself down whenever it detects some shorted component inside secondary side. One superior example was the capability supply utilised in printer. Printers as a rule have two boards; one was the strength supply while the other was main table. If there is any short-term circuit in the main board, the power supply would not work. In order to isolate for where help, one must remove the connector in the power furnish board. Once the supply connector on the main table was taken off, you are now able to switch on the printer and check if there is any voltages present at the power furnish connector. 585 Watt Hot Swap Power Supply may be appropriate for you computer.
If there are actually zero voltages scored across all the supply (VCC) hooks then we could conclude that power give have problem and put your whole concentration in such a power supply board. Can you imagine if there are voltages measured along the connector? Which means the significant board is actually causing this no power problem most probably due for some shorted components primarily board.
About the Author:
Check your updates with DL585 870WATT , visit my website about Redundant Power Supply and other accessories.
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment