Setting Your own IDE Drives the Right Way
In case you have a pc which you purchased around a couple of years ago, you have an IDE hard disk drive. Though any such hard drive is right now being replaced by way of the faster Serial ATA, or sata external enclosure , configuration drives, there holds a lot of computers that have IDE drives inside them. As the years go by, there may come a time when you need to restore or create another IDE drive for a computer. In such case, you need to know how to line your IDE drive properly.
Your serial ata hard drives could easily be identified by looking at the kind of cable which connects them to your pc. As instead of the SATA cable which appears like a flat electrical cable, IDE hard drives use a broad, thin, and ribbon-like data interface connection called ATA-7 which unfortunately has three forty-sockets, one afre the wedding that connects on the motherboard, one on the middle and a replacement at the other end for every single pins found in the rear of your hard drive.
If you have to augment your storage devices with another IDE drive, you will need to configure it in such a way that an individual becomes the most crucial drive and also the second one becomes that secondary generate. Naturally, it is important to set the new drive as the secondary considering your old hard disk contains the operating system for your personal computer.
Well, that is unless of course you wanted your new IDE drive to maintain your main system then you have to set it for the reason that primary and also the expert, but that would mean reformatting and installing the operating system on it, not to mention the drivers that computer must have and an array of software applications that you use. If you would like make that simple, you'll be able to just set the new drive since secondary storage devices.
At the back of each hard disk, there is mostly a small spot immediately to the right with the 40-pin socket that contain eight pins in a four-pair configuration. This is the master and slave, or the most crucial and a second set of selector. You may normally discover a small jumper in that selector. Look at the label onto your hard drive and see the adequate jumper arrangement for master or servant. If you want to have the new drive are a servant, then merely follow the configuration as shown with the illustration on the label with the hard drive.
Your serial ata hard drives could easily be identified by looking at the kind of cable which connects them to your pc. As instead of the SATA cable which appears like a flat electrical cable, IDE hard drives use a broad, thin, and ribbon-like data interface connection called ATA-7 which unfortunately has three forty-sockets, one afre the wedding that connects on the motherboard, one on the middle and a replacement at the other end for every single pins found in the rear of your hard drive.
If you have to augment your storage devices with another IDE drive, you will need to configure it in such a way that an individual becomes the most crucial drive and also the second one becomes that secondary generate. Naturally, it is important to set the new drive as the secondary considering your old hard disk contains the operating system for your personal computer.
Well, that is unless of course you wanted your new IDE drive to maintain your main system then you have to set it for the reason that primary and also the expert, but that would mean reformatting and installing the operating system on it, not to mention the drivers that computer must have and an array of software applications that you use. If you would like make that simple, you'll be able to just set the new drive since secondary storage devices.
At the back of each hard disk, there is mostly a small spot immediately to the right with the 40-pin socket that contain eight pins in a four-pair configuration. This is the master and slave, or the most crucial and a second set of selector. You may normally discover a small jumper in that selector. Look at the label onto your hard drive and see the adequate jumper arrangement for master or servant. If you want to have the new drive are a servant, then merely follow the configuration as shown with the illustration on the label with the hard drive.
About the Author:
We offers knowledge about fiber channel hard disk , visit my website about scsi to sata and information to help you with computer components.
You are receiving this because you signed up for it on 2011-10-03 from IP 203.109.66.181
To fine-tune your selection of which articles to receive, just login here
using your username:
To unsubscribe please use the following link:
Unsubscribe
No comments:
Post a Comment